Machines/GUK · SM
GUK SM 70/2
Each job you run comes with its own specific problems, and more often than not the culprit is found on the tooling shafts. The standard finishing tools supplied with your machine aren’t accurate, versatile or delicate enough for the results you and your customers expect. At Technifold we design and build bespoke, retro-fit premium finishing tools to solve both common and complex finishing problems.
Your SM 70/2, finished properly.
What we solve
Problems we eliminate on the SM 70/2
Eliminate fibre crackingCracked colour on the fold, on digital, coated or cross-grain stock. The steel score that causes it, and what replaces it in minutes.See how we eliminate it →
True micro-perforationRagged bursts, paper dust, stacks that will not lie flat. The coarse perf wheel that causes it, and the blade that replaces it in minutes.See how we eliminate it →
Guillotine-quality cuttingFuzzy, dusty edges and a second pass at the guillotine. The crush-cut slitters that cause it, and the scissor-action tool that replaces them in minutes.See how we eliminate it →
Section scores that holdSections that spring open, gusset at the head and fight the stitcher. The barely-there steel score that causes it, and the deep, defined score that replaces it.See how we eliminate it →
Pharma leaflet scoringTorn scores and wrinkled folds on thin, highly-folded leaflet work. The abrasive steel score that causes it, and the six-setting pharma score that replaces it.See how we eliminate it →
Book cover creasingSpine and hinge creases in one pass, in register, without cracking. The cover work you send out, done on the folder you already run.See how we eliminate it →
Close-proximity finishingCrease beside cut, crease beside perf, cut beside perf, or doubles of any of them. One housing, six set-ups, no letterpress bill.See how we eliminate it →
Crease with perfs both sidesThe perf-crease-perf pattern for stubs and tear-offs, packed into millimetres, in one pass. The specialist tool for work that otherwise goes to letterpress.See how we eliminate it →
Custom & OEM toolingA part that is obsolete, impossible to source, or never existed. If it is a wheel, a blade, a rib or a holder that touches paper or board, we can probably make it.See how we eliminate it →
Compatible tooling
Tools compatible with the SM 70/2
Tri-CreaserTech-ni-Fold's flagship creasing tool; eliminates fibre cracking on 85-350gsm stocks at folding machine speedSee the Tri-Creaser →
Micro-PerforatorProduces fine, flat, distortion-free micro-perforations from 17 TPI upwards; blades cut against a Nylon Sleeve for long life and clean perfed lines that run through laser printersSee the Micro-Perforator →
Cutting ToolProduces a single cut or two cuts in close proximity on paper or card; guillotine-quality slitting via scissor-action designSee the Cutting Tool →
Multi-ToolVersatile multi-operation tool performing cutting, perforation, and optionally creasing in close proximity on a single shared holderSee the Multi-Tool →
Advance-DSF UpgradeFemale-only pack to add Advance-DSF (Direct Surface Feed) digital print capability to existing Tri-Creaser toolsSee the Advance-DSF Upgrade →
Gripper BossAuxiliary support rollers that grip and feed sheets through a finishing device during operationSee the Gripper Boss →
CP ApplicatorSpecialised finishing tool for one centre crease with a micro-perforation either side, in close proximitySee the CP Applicator →
Spine-Hinge CreaserCreates spine and hinge creases on book covers via a folding machine or standalone creaser (1 to 4 simultaneous crease lines, spine and hinge widths adjustable per job)See the Spine-Hinge Creaser →
Section-ScorerCreates deeper, well-defined score lines on section work for cleaner, more reliable foldsSee the Section-Scorer →
Pharma-ScoreScoring device for pharmaceutical leaflets and instructional documents needing multiple tight folds in small packagingSee the Pharma-Score →
The next step
Tell us the jobs you run on your GUK SM 70/2
We’ll email you exactly what fits your machine and what it costs, specified by the engineers who make the tools, not picked from a catalogue.
No payment details, no commitment. If it looks right, your first 30 days on the machine are free. A money-back promise has backed this tooling since 1999.
25 years · 45,000+ tools running worldwide