Tooling for Count machines

20 Count machines mapped · 16 problems we solve on them

Our tooling retro-fits to the shafts your Count machines already have, so they crease, perforate and cut to a standard the original tooling was never built for. Find your model below, or tell us what you run and we’ll email you exactly what fits.

Email me exactly what fits my machine →

Count creasing machines

7 models

Add folding to this machinePerfect creases, flat sheets, hand-folding after. The Card Folder couples behind your creaser and folds on the crease, up to 350gsm, five fold types.Rotary creasing on your shaftsIf your machine has tooling shafts, we can put proper creasing on them: crack-free, colour-coded profiles, chosen per job, at full running speed.Rotary micro-perf on your shaftsTear-offs, coupons and reply forms, perforated inline. Ten blade pitches from coarse tear to a line that looks printed, on the shafts you already have.Rotary cutting on your shaftsSlits, edge trims, cut-outs and kiss cuts, inline. A true scissor shear against a hardened boss, on the shafts you already have.Custom & OEM toolingA part that is obsolete, impossible to source, or never existed. If it is a wheel, a blade, a rib or a holder that touches paper or board, we can probably make it.

FC114

Creasers

iCrease

Count rotary creasers

4 models

PerfMaster

Count knife folders

2 models

Eliminate fibre crackingCracked colour on the fold, on digital, coated or cross-grain stock. The steel score that causes it, and what replaces it in minutes.True micro-perforationRagged bursts, paper dust, stacks that will not lie flat. The coarse perf wheel that causes it, and the blade that replaces it in minutes.Guillotine-quality cuttingFuzzy, dusty edges and a second pass at the guillotine. The crush-cut slitters that cause it, and the scissor-action tool that replaces them in minutes.Section scores that holdSections that spring open, gusset at the head and fight the stitcher. The barely-there steel score that causes it, and the deep, defined score that replaces it.Pharma leaflet scoringTorn scores and wrinkled folds on thin, highly-folded leaflet work. The abrasive steel score that causes it, and the six-setting pharma score that replaces it.Book cover creasingSpine and hinge creases in one pass, in register, without cracking. The cover work you send out, done on the folder you already run.Close-proximity finishingCrease beside cut, crease beside perf, cut beside perf, or doubles of any of them. One housing, six set-ups, no letterpress bill.Crease with perfs both sidesThe perf-crease-perf pattern for stubs and tear-offs, packed into millimetres, in one pass. The specialist tool for work that otherwise goes to letterpress.Custom & OEM toolingA part that is obsolete, impossible to source, or never existed. If it is a wheel, a blade, a rib or a holder that touches paper or board, we can probably make it.

KF

Count coating and laminating machines

1 model

Machine-direction creasingCrease down the web at full press speed. No offline pass, no rotary die registration risk, no slowing the line for finishing.Micro-perforation on the webTear-off work perforated down the web, flat enough to keep processing and clean enough to tear by hand. Ten pitches, inline, no speed loss.Every finish, one cassetteCrease, score, perforate, cut and kiss-cut in any combination across the web. One retro-fitted cassette, reconfigured per job.Custom & OEM toolingA part that is obsolete, impossible to source, or never existed. If it is a wheel, a blade, a rib or a holder that touches paper or board, we can probably make it.

CountCoat

CountCoat GT

Other Count machines we hold

We haven’t written up a specific problem for these yet. That doesn’t mean we can’t help: if a machine has rotary shafts of any description, our tooling can replace what’s on them — see rotary creasing, micro-perforation and cutting. We engineer everything ourselves, so tell us what you run and we’ll work it out.

counting and numbering machines

Tell us which Count you run.

We’ll email you exactly what fits and what it costs, specified by the engineers who make the tools, not picked from a catalogue.

Name *Work email *

Machine makeModelCan’t see your machine? Tell us what you runWe build for machines that aren’t on this list all the time. Say what you have and we’ll work it out.

Anything else we should know?

No payment details. No commitment. A money-back promise has backed this tooling since 1999.